Loading... Please wait...

our newsletter

Account Navigation

  • Wish Lists
  • My Account
  • Order Status
  • CR-4000P Comb Raiser
  • CR-4000P shown on Rem 870 and H&R Shotguns

Accu-Riser CP-4000P Monte Carlo Comb Raiser

Your Price:
0.50 LBS
Free Shipping


Product Description

This model of our original molded hard rubber comb raiser,  can be mounted permanantly to a rifle or shotgun stock by drilling two holes and afixing it with two #10 screws, sort of like attaching a recoil pad. Comes with two screws and rubber plugs to plug holes drilled in the top of the pad. We do not recomend this model for bolt action rifles as it may interfear with the cycleing of the bolt and also the cleaning of the barrel from the breech. Best used on single shot , pump or auto loading rifles and shotguns. Height of pad is 1 1/4".

Find Similar Products by Category

Product Reviews

Write review

Showing reviews 1-10 of 12 | Next

  1. Excellent Product

    Posted by Unknown on 6th Feb 2021

    The comb riser does what it's supposed to do. I've installed it on several rifles and it always fits properly. The 4000P adds just the right amount of height for proper sight picture every time.

  2. Very good

    Posted by Unknown on 3rd Nov 2020

    I mounted it on my old Husqvarna 1640 and I orderd one more for my Valmet 412s cal 12/222 rem.


    Posted by JIM on 31st Oct 2020


  4. Mounted to Izh18 shotgun

    Posted by andris.vagalis@gmail.com on 23rd May 2019

    Nice cheek riser. Fit very well for standard stock. Can be used only for the right-hand shooter.

  5. Perfect

    Posted by David on 15th Jun 2015

    This Accu-Riser is the PERFECT add on for anyone who owns a Savage MKII FV-SR. It brought my cheek weld right where I needed it. Installation was a snap. I love this thing.
    It gave new life to the cheap factory stock of my FV-SR. So glad I found this product at The Leatherman. Thanks.

  6. Did the trick

    Posted by ZBeard on 10th Nov 2014

    I bought this product for a Savage Mark II FV-SR. The FV comes with a little plastic stock, and with a scope mounted there was basically no place for a cheek weld. I installed an Accu-riser, and what a difference it made! It fixed the cheek weld problem and turned that el-cheapo plastic stock into something special. Best $35 I've spent in quite a while.

  7. Mounted to a Ruger M77 Mark ll whit Houge stock

    Posted by Unknown on 30th Jun 2014

    Easy to Mount, perfect fit and it does not interfere with the bolt.

  8. Mounted to a Savage FVSS Synthetic Stock

    Posted by George on 2nd Jan 2013

    This Cheek Riser was easy to position and custom fit to the contours of my stock (i.e. sands well and is flexible), readily accepts a variety of paint(Krylon Camo for instance), big improvement in scope acquisition (I'm finally getting a quick, full picture from my rear objective), does not interfere with bolt retraction (you might need to sand down the top a bit) and is comfortable against my face. I skipped using the two screws and just glued it to my stock (epoxy, with duct tape straps to hold in place while drying). All in all a nice piece.

  9. Works Great for SX3 Slug Gun

    Posted by JML on 1st Oct 2012

    Winchester SX3 Cantilever Slug Composite Stock
    This product fit my stock perfectly. I was having a lot of trouble getting aligned with my 2-7 leopold and this riser brought me right up in perfect alignment. It mounts solidly and blends in well with the black composite stock. I think it's a better solution that the neoprene when you are looking for a permanent fix. This is a dedicated slug gun for me so it works well. Like the directions indicate, don't over tighten the screws!!

  10. Great Product !!!

    Posted by Antonio on 2nd Jun 2012

    The product arrived very fast. It's very easy to install and very solid once installed. It looks nice on my Savage 111.

Showing reviews 1-10 of 12 | Next

Back to Top

Click the button below to add the Accu-Riser CP-4000P Monte Carlo Comb Raiser to your wish list.