Our new ambidextrous design comb raiser comes with everything needed to fit most rifles and shotguns. Kit includes two interchangeable rubber pads, 1/2" and 1", that snap onto the hard molded nylon base. This allows an increase to the comb of the stock from 5/8" to 1 1/8" which will correct most eye alignment problems with rifles and shotguns that are not designed for use with optic sights or those mounted with large belled optic sights. Base can be temporarily mounted with supplied velcro cinch strap and double sided tape with no damage to stock or mounted permanently with two supplied #8 screws by drilling two 5/64" holes in stock and fastening with screws on top of base. Rubber pads snap over top to give unit a clean custom look as part of the stock. This matt black version looks great on black synthetic stocks but we also have available our 3m Walnut vinyl Veneer kit and our own camoflauge Vinyl Veneer Kit to custom match to your stocks color. The rich Walnut veneer looks like the real thing . The Camo veneer is our own design which comes close to most licensed camo patterns being used on shotgun and rifle stocks.Choose which version on the bottom when ordering. This cheek pad has been designed to fit most classic styled stock designs found on shotguns and most sporting rifles. Will not fit thumb hole stocks. Base can be trimmed underneath to allow additional width for some wider stocks. Some long bolt action rifles require the cheek pad to be mounted farther back on the stock to clear the throw of the bolt. Please check this clearance before mounting the cheek pad . If you feel this cheek pad will not fit your stock, you may return it for a full refund.
Showing reviews 1-10 of 28 | Next
Posted by Bruce W. Fletcher on 4th Aug 2015
I own a couple of Remington model 721 rifles in 270 and 30-06. Both of these guns are very accurate. However when the rifles were made in the late 40s the stocks were designed to be used with open sights. The comb of the stocks are lower than a modern stock. With a scope it's almost impossible to get a decent cheek weld. I searched for an answer for some time until I found this product. Both rifles now put your eye right on the cross hairs when you throw the rifle up to your shoulder. Very Happy with the results.
Posted by scott on 5th Jun 2015
this is the ticket for my 22lr rifle, dont know that i'd put it on my 308, but it works well for my savage 64.
Posted by Mike on 6th Mar 2015
I have a Tikka T3 Lite. It fit the stock well and was very easy to install and I was able to line up my scope perfectly. And the quality is great.
I would highly recommend this.
Posted by Steph on 27th Feb 2015
Looking for a solution to aligning your eye to scope axis? Look no farther than The Leatherman CR-6000. This uniquely simple, universal cheek rest is clean, easy to install for temporary or permanent use and can ajust to about any level of scope axis by following the simple instructions. If cosmetic symmetry is your concern, The Leatherman offers many color options from black to camo! I have recommended this product to many of my friends.
Posted by Unknown on 20th Feb 2015
Great product for trap shooting. Need additional foam tape if you want to secure to gun without using screws.
My main purpose is to increase Point of Aim for my O/U shotgun. The 5/8 " is enought to raise POI about 5"
Posted by tim on 21st Dec 2014
I ordered this product for my girlfriends 870. the comb on her 870 was too low for her to shoot clays. After receiving the accuriser and installing it I handed her her shotgun and she exclaimed "this is perfect"!
Posted by Tamas on 28th Oct 2014
I have an Cz 550 LUX 308 hunting gun. This riser had the height I needed for that scope line. I can now comfortably shoot my rifle without shifting my face. I will likely recomend this product to my friends. It is well Made and a good value.
Wery fast shipping.
Thank you so much.
Posted by Unknown on 30th May 2014
I bought this product for my Mosin Nagant 91/30. I have a Jmeck see though scope mount, so the scope sits very high .
This riser had the height I needed for that scope and the strap does not interfere with the dog collars through the stock for the sling.
The Mosin has a very wide stock and is flat on top toward the back. I had to sand the riser with a dremmel tool as suggested by the directions. The riser fits ok but I have a small gap at the back because of the very thick stock. This does not interfere with the function. A small spacer of some sort could probably be used to fill the gap but I felt it was not needed. It looks ok.
I can now comfortably shoot my rifle without shifting my face because a lack of cheek weld. I will likely recomend this product to others. It is well Made and a good value.
Posted by Bill on 9th Jan 2014
I installed this on my Mosin Nagant M91/30. Certainly not an exact fit. The Nagant's stock design is such that I couldn't get it to stay exactly in place with the strap so attached it with the screws. The fit required sanding as the Nagant stock is wide. I still had a gap at the rear which doesn't seem to matter... very tight steady mount. Having said this, the riser is not designed specifically for my rifle and the Nagant has a military stock and is very old fashion in shape. Service was EXCELLENT and fast and the price was right. I've done a lot of shopping for a cheek riser for this rifle and none of the others come close. I'd do it again.
Posted by Ryan on 30th Sep 2013
I installed the Accu-Riser Cheek Pad on my Stoeger Condor, which i use for shooting skeet. It was a tight fit getting the pad on the stock but the Condor's stock is a little wider than most shotguns. I had to widen the pad by cutting off the inside ridge, with a utility knife, and i also used a dowel with sand paper to widen the pad's circumference. Even after the modifications i made to the pad it was still a tight fit, so, i had to fasten the pad with the provided screws in order to secure a proper fit. If i were putting the pad on my Remington i could of used the provided straps to secure its installation with no problem. Once i got the pad on you could not see any of the modifications i had made on the inside face. Also, I really liked the pads color, it matches my recoil pad very well. For my needs i used the half inch pad, and boy let me tell you what, it was like night and day! the half inch rise gave me a perfect gun fit. I can now mount my gun with my cheek firmly pressed on the stock wile maintaining correct eye alinement. This is a big plus for me when shooting skeet. There are two thing i did not like about the pad. I wish the pad was a little longer, its only around 5 inches long. Also, i which they made a one-piece pad that was 5/8" high. All in all this pad was a great buy for me and i will recommend it to others!
Showing reviews 1-10 of 28 | Next